Negnon Gamma Waders
Negnon Gamma Velorum
Negnon Gamma Velorum is a higher model in the Negnon wader line. It has been developed for anglers who expect a stronger construction, high waterproofness and better performance. The legs are made from four-layer fabric, while the upper part of the waders is made from three-layer fabric.
The construction of Gamma Velorum uses materials and solutions typical of solid waders from the medium segment of the market. It is not built as the cheapest possible product, but as a well-designed functional wader offered at a very favourable price.
The favourable price does not result from simplifying the construction or saving on the most important parts of the product. It comes from the direct sales model — the brand sells the product directly to the customer. As a result, the angler receives waders made from good materials, with a modern design, refined details and construction solutions often found in more expensive models.
In practice, this means that more of the value remains in the product itself: in the fabric, performance, cut, seams, pockets, socks and other functional elements, rather than in the traditional chain of wholesalers, distributors and shops.
Facts
- The waders have a 4/3-layer construction.
- The legs are made from four-layer STREAMTEX® GT fabric.
- The upper part of the waders is made from three-layer STREAMTEX® GT fabric.
- The waterproofness of the material is 20,000 mm.
- The breathability of the material is above 6,000 g/m2/24h.
- The four-layer fabric in the legs increases resistance in the areas most exposed to wear.
- The three-layer upper part helps reduce weight and improves comfort during use.
- The construction has been designed to reduce the number of seams and fabric joints.
- There is only one seam in the leg.
- The leg seam is positioned on the outside.
- The waders are fitted with neoprene socks.
- The underside of the sock is thicker.
- The underside of the sock is additionally covered with a rubber print, which helps keep the foot more stable inside the boot.
- The waders have built-in neoprene gravel guards.
- There is an elastic drawcord at the upper part of the waders.
- There is a rear hanger for attaching a landing net or hanging the waders after use.
- The waders have a large external pocket closed with a splash-resistant YKK zip.
- Inside, there is an additional pocket closed with a YKK zip.
- The waders have belt loops: a double loop at the back and single loops at the front.
- There is a Velcro attachment point for a fly patch on the front.
- The fly patch is included in the set.
- A wader bag with the Negnon logo is included.
Summary
Gamma Velorum is not a product based only on the promise of a low price. These waders are built around a different idea: good materials, proven construction, modern appearance, practical details, a known source of origin and a price resulting from direct sales to the angler.
1. Sizing and fitting before use
Choose the size according to the actual model’s size chart, taking body and foot measurements into account. Also allow for the clothing worn underneath the waders. Try on the waders with the clothing and boots you will use when wading. Check your freedom of movement: sit down, squat and lift a knee as if stepping up onto a high step. The fabric should not be under excessive tension at the crotch, knees or joins. Adjust the braces and belt. Waders that are too tight can cause excessive tension and damage to the fabric, particularly around the crotch, knees and seat. Waders that are too loose can lead to folds and increased friction, accelerating fabric wear. The neoprene socks must fit properly, without squeezing or bunching inside the wading boots.
2. Cleaning after use
Rinse off mud, sand and other dirt with clean water. After contact with salt water, rinse the waders thoroughly with fresh water. Remove sand from around the socks, guards and zips. Avoid vigorous scrubbing of the material and joins.
3. Washing
Always wash the waders in lukewarm water. Hot water can weaken glued joins, which may cause seam tape to peel away and damage the membrane laminate. We recommend gentle hand-washing with a detergent intended for membrane garments. Rinse detergent residues thoroughly. Do not use fabric softeners, bleach, solvents or aggressive cleaning agents. Do not machine-wash the waders unless the label for this model explicitly permits it. Always follow the care instructions on the label.
4. Drying
Dry both the outside and inside of the waders thoroughly, especially the insides of the neoprene socks. Dry them in a well-ventilated place, in the shade, away from heaters, flames and other sources of heat. Do not put wet waders in a sealed bag or leave them in a car.
5. Protecting the material and socks
Put on and remove the waders carefully, without pulling roughly on the material, socks or joins. Do not walk on the ground in neoprene socks alone—use suitable wading boots. Before putting on the boots, check that there is no sand or grit inside them.
6. Storage
Store the waders completely dry, in a well-ventilated place, loosely laid out or hung up, without sharp folds in the material, socks or zip. Protect them from high temperatures: do not leave them in a hot car, beside a heater or in the sun. Do not store wet waders in a sealed bag or container. Heat combined with moisture can accelerate the degradation of materials and joins.
7. Water repellency treatment (DWR)
Regularly check the water-repellent properties of the fabric. If water no longer forms droplets on its surface and begins to soak into the outer fabric, we recommend renewing the DWR treatment. Use only products intended for breathable membrane clothing, according to their maker’s instructions. Avoid products requiring fixing at high temperature. Remember that DWR treatment does not replace the waterproof membrane and is not intended to remedy leaks.
8. Inspection and repairs
Regularly check the condition of the material, joins, socks and zips. Respond to the first signs of wear: abrasions, minor damage, peeling seam tape or leaks. Repair them before further use or contact TAIMEN service. Do not wait until the damage grows. For repairs, use only materials intended for repairing membrane garments or neoprene, depending on the part being repaired.