Taimen Onon Wading Boots (studs incl)
Size Charts
Taimen shoe sizes are based on US shoe sizes.
To properly choose the size of the shoe for your foot, you need to consider the neoprene sock. In practice, this means ordering a shoe one size larger than your everyday shoe size.
To do this, select the Taimen shoe size (Taimen Size based on US) and find the corresponding size in the table.
For example: If you normally wear size 42 (EU) shoes, you should choose size 10.
| Size (based on US sizes) | Shoe number | Foot length in cm | Insert length in cm (total length inside of boot) |
|---|---|---|---|
| 8 | 39 1/2 | 25 | 27 |
| 9 | 41 | 26 | 28 |
| 10 | 42 | 27 | 29 |
| 11 | 43 1/2 | 28 | 30 |
| 12 | 45 | 29 | 31 |
| 13 | 46 | 30 | 32 |
If you cannot find the correct shoe size, you can use a shoe insert that reduces the size by about half a size.
Facts:
Mid sole is made out of a light and flexible material. Due to the flexibility of the used material the sole have better contact with the river floor, providing a better grip.
Rubber sole adapted to screwed in studs. Inside part of sole additionally reinforced with 4 mm hard rubber - in place where studs go in(with sole 8 mm).
Mounted studs protrude high, thus providing a good grip while wading.
Rubber sole Special rubber mix selected for wading on slippery surfaces. The shape of the sole based on honeycomb provides the possibility of screwing the appropriate number of studs according to fishing conditions.
1. Sizing and fit check before use
Choose the size according to the actual model’s size chart. Check the fit when trying them on: put on both boots with the waders and socks you will use when wading, and adjust the lacing evenly. Check that your toes have room to move without pressing against the front of the boots, that the heels remain stable, and that the neoprene socks do not bunch up inside. Boots that are too tight may cause pressure and excessive strain on the materials and joins. Boots that are too loose may increase friction, accelerating wear to the lining and neoprene socks.
2. Cleaning After Use
After every use, rinse the boots with clean water, removing mud, sand and plant debris. After contact with salt water, rinse them thoroughly with fresh water. Also clean the interiors, tongues, laces, eyelets, lace hooks and surrounding areas. Check that the water drainage openings are clear. Gently remove dirt with a soft brush.
3. Washing and Cleaning Products
We recommend hand-cleaning in lukewarm water. If necessary, use a mild cleaner suitable for the materials from which the boots are made, and rinse out any residue thoroughly. Do not use bleach, solvents or aggressive cleaning products. Do not machine-wash the boots or use a pressure washer. Choose care products for the particular model; products intended for natural leather are not necessarily suitable for synthetic materials.
4. Drying
Loosen the laces and open the tongues to allow air to circulate. If the insoles are removable, remove them and dry them separately. Thoroughly dry the interiors, uppers and soles. Dry the boots in a well-ventilated place, in the shade, away from heaters, fire and other heat sources. Do not speed up drying with hot air.
5. Sole Care
Regularly remove dirt from the tread. On models with felt soles, thoroughly rinse and gently clean the felt, then leave it to dry completely. Before moving to another fishing water, clean and dry the whole pair of boots to reduce the transfer of aquatic organisms between waters. Rinsing alone does not replace disinfection required at that fishing water.
6. Laces and Studs
Loosen the laces before putting the boots on and taking them off. Do not take a boot off by standing on its heel with the other boot. If studs are used, regularly check their fastening and wear. Use only studs compatible with the particular model and sole, as instructed. Screws that are too long may damage the boot.
7. Storage and Protection from Overheating
Store the boots clean and completely dry in a cool, well-ventilated place. Do not leave them in a hot car, near a heater or in direct sunlight. Do not seal damp boots in a bag or container. Heat and moisture can accelerate material degradation and damage bonded joints.
8. Inspection and repairs
Regularly inspect the uppers, seams, reinforcements, eyelets, hooks and the sole attachment. Respond to the first signs of damage: wear, cracks, loose parts or sole separation. Replace worn laces and studs. Repair damage before further use or contact TAIMEN service. Do not wait for the damage to grow — continued use can make repair more difficult. Use repair methods and materials intended for wading boots or use a professional repair service.